...
The mapping assistant has 3 modes, an information bar and an advanced section options:
...
Nr number: how many elements of the same kind are present mapped
ID identifier: the unique identifier of the element
...
C#: canvas number
B#: basecircuit number
Z#: zone number
P#: pipe number
Revit element ID: Is a decimal number (int) that identifies an element in a Revit project. It is unique in that same project, but not among several models. Its length may vary depending on the number of elements in a model, but rarely exceeds 8 digits. (more information on selecting Revit elements by ID https://help.autodesk.com/view/RVTLT/2024/ENU/?guid=GUID-2B1CC22C-CB1F-45DA-B57B-62C36013D9E0 )
Type: type of the element
Pipe
Zone
Component
internal pipe (pipe within a basecircuit)
Location: where is the element located
...
Show suggestions is a tool that helps you to map the components, pipes and zones of your models. It works by analysing the data and finding the best matches for each element. Hysopt BIM syncer uses the system topology and the classification for finding matches. If the mapping assistant cannot find any suggestions for an element, you will have to map it manually. This will also help the mapping assistant to learn from your input and improve its suggestions for other elements.
...
Refresh
To see updated suggestions, you need to press the refresh button. This will trigger a new search and display new suggestions for your mapping task.
...
The mapping assistant assigns a probability to each suggestion, which indicates how likely it is that the suggestion is correct. The higher the probability, the more confident the mapping assistant is about the suggestion. You can find the probability in the information bar. A way to improve the quality of your suggestions is to use a the probability threshold. This means that you can specify a minimum value for the probability of each suggestion, and only those that meet or exceed this value will be displayed. For example, if you set the probability threshold to 0.8, you will only see suggestions that have at least 80% probability of being correct or relevant.
...
in advanced options. The workflow is to start with a high probability and lower this when the mapping assistant is not able to find any suggestions.
Show Mappings
...
Unmap
The unmap button allows you to remove the association between elements that have been previously mapped. This is useful if you want to correct a mapping error.
...
With the navigate buttons, you can navigate through the mapped elements.
...
Information bar
Map manually messages
...
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Hysopt element of the type ‘…' {Hysopt component name} and BIM element of type ‘family name’ {BIM element type} have the same classification. |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Hysopt element of type {Hysopt component name} and BIM element of type {BIM element type} are located on the same branch ({location}) |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Hysopt element of type {Hysopt component name} and BIM element of type {BIM element type} are on the same branch of the same location ({location}) |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Hysopt element of type {Hysopt component name} and BIM element of type {BIM element type} are on the same branch of the same location ({location}) connected to an already mapped element |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Both branches end up in a component or node that is mapped onto each other |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Both branches end in a component mapped onto each other, and are on the same location |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Both branches are connected to the same element on the same location ({location}) |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Both branches are on the same location ({location}), connected to an already mapped element, and the branch ends seem equivalent |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Both pipe segments represent the same branch |
Panel | ||
---|---|---|
| ||
[suggestion #/#] [Probability #%] Hysopt zone ({Hysopt zone}) and BIM space ({BIM space}) contain the same components |
Panel | ||
---|---|---|
| ||
No suggestion found with minimal suggestion probability of 0%#%. try Try to map some elements manually to find new suggestions. |
...
Automatically navigate to objects
The option ‘automatically navigate to objects’ means that when a mapping suggestion or a confirmed mapping is shown in the mapping assistant, both your Hysopt and Revit view will zoom in and focus on that element, and also highlight it for better visibility. This can help you to quickly identify the elements in both applications. To enable this feature, you need to check the checkbox for 'automatically navigate to objects' in the mapping assistant.
Minimal suggestion probability
This means that you can specify a minimum value for the probability of suggestions, and only those that meet or exceed this value will be displayed. For example, if you set the probability threshold to 80, you will only see suggestions that have at least 80% probability
...
Highlight duration (in seconds)
Remove all
Highlight all
- images
- only first element
- mem cache
- file cache
of being correct or relevant.
Remove all
Remove all the implemented mappings. In a pop-up window, you need to confirm that you really want to remove all mappings.
...
Info |
---|
There is no possibility to undo this action. |
Highlight all
Highlight all implemented mappings.
...